Prerequisite

• PC or MAC
• AG-702 Device
• LAN Cable
• WiFi
• Power Supply for Gateway
  

Steps in installing Edge Lite for Atreyo devices

1. Obtaining Edge Lite setup files
2. Accessing the web interface of the AG-702
3. Installing Edge Lite
4. Accessing the web interface of Edge Lite

Obtaining Edge Lite set up files

1. libopenssl1.1_1.1.1t-1_mipsel_24kc.ipk
2. zoho_iot_agent_0.2.4-1_mipsel_24kc.ipk

Note: The version number of the files you receive may differ.

Accessing the Web Interface of the Atreyo device

• Wi-Fi
• WAN
• LAN 

Using Wifi

1. Turn on the gateway and wait a few minutes until the Wi-Fi light on the device turns on.
2. On your Mac or PC, search for available Wi-Fi networks.
3. Select AG-702 and connect to it using the default password given below:
   

   Password: atreyo12
   

   
   

   
   

   Note: If you have previously connected via Wi-Fi and changed the password, use your updated password to connect.

4. Once connected, open a browser and enter the following IP address in the address bar:
   

   IP: 192.168.1.1
   

   
   

   
   

   
   

   
   

   
   

   Note: Click Continue to site if prompted.

5. You’ll be directed to the gateway’s web interface. Log in using the credentials below:
   Username: root
   Password: root
   
   
   
   
6. After logging in, you’ll be prompted to update your password.

Using WAN  

1. Connect the WAN port of the AG-702 gateway to your router using an Ethernet cable.
2. Power on the gateway and wait for the WAN LED indicator to turn on.
3. On your Mac or PC, ensure you're connected to the same network as the router (wired or wireless).
4. Obtain the IP address of the Gateway device from your routers DCHP list.
   
   
   
   
5. Open a browser and enter the IP address assigned to the gateway by your router.
   
   
   
   
6. In the gateway’s web interface, log in using the default credentials:
   Username: root
   Password: root
   
   
   
   
7. After logging in, you'll be prompted to update your password.

Using LAN  

1. Connect your Mac or PC directly to the LAN port of the AG-702 gateway using an Ethernet cable.
2. Set a static IP address for your system in the 192.168.1.x range (except 192.168.1.60, which is the gateway).

• Example: 192.168.1.21
• Subnet Mask: 255.255.255.0 

For Mac,

You can configure this by navigating to:

System Settings > Network > [LAN Adapter] > Details > TCP/IP

Set Configure IPv4 to Manually, then enter the static IP and subnet mask.

For Windows,

You can configure this by navigating to:

Control Panel > Network and Internet > Network and Sharing Center > Change adapter settings

• Right click on the Ethernet icon (corresponding to your LAN connection) and select Properties.
• Double click Internet Protocol Version 4 (TCP/IPv4)
• Select Use the following IP address.
• Enter the IP address and subnet mask

3. Open a browser and enter the following IP address in the address bar:
   IP: 192.168.1.60
   
   

4. The gateway’s web interface will load. Log in using the credentials:
   Username: root
   Password: root
   
   
   
   
5. After logging in, you’ll be asked to update your password.

Installing Edge Lite

1. Go to System > Software.
   
   
   
   
2. Click Upload Package > Browse.
   
   
   
   
   
   
   
3. Navigate to the location where you have stored the Edge Lite files.
4. First, select libopenssl1.1_1.1.1t-1_mipsel_24kc.ipk, click Open, and then click Upload.
   
   
   
   
   
   
5. Once the file is uploaded, click Install.
   
   
   
   
6. Repeat the same steps to upload and install zoho_iot_agent_0.2.4-1_mipsel_24kc.ipk.

Note: The order of installation is important. The files must be installed in the exact sequence shown above.

Accessing the web interface of Edge Lite

• Wi-Fi method: 192.168.1.1:8070
• WAN method: 192.168.0.114:8070
  Note: The WAN IP address may vary depending on your DHCP settings.
• LAN method: 192.168.1.60:8070